Let’s Construct a Laundry Drawer!
DIY Laundry Drawer Plans
$9.99
Supplies I Used to Construct the Laundry Drawer
Step 1: Reducing Items for the Drawer
It takes 7 components to make the physique. So not many. If you need a set laundry drawer plans with dimensions then I’ve that out there, it additionally comes with a CNC reduce file if in case you have a CNC. I personally painted my cupboards so I simply used no matter 3/4” sheet materials I had scraps of which is MDF on this case.
I begin by laying the facet items on their again and attaching what would be the backside. When becoming a member of issues collectively, it will likely be the identical course of on all the things, I used DAPs weldwood wooden glue then predrill and run in a screw
Step 2: Making ready the Toe Kick Plate and Attaching Laundry Drawer Sides
This ledge right here will probably be the place the toe kick plate goes in, which is that this board right here. I’m utilizing it as a spacer to ensure the underside is hooked up sq.. After utilizing it to align the board from the within, I additionally used it as a spacer to information me on the place to pre drill and run in a screw. Double checking that it labored; it did, so I proceed attaching. I used this trick once more after I wanted to run within the middle gap. So long as the board is flush to the entrance, it is going to point out the place the three/4 materials begins for the pre drill gap.
After attaching the primary facet, I hooked up the second facet the identical method. Nevertheless because the toe kick now can’t match inside to examine for sq., I simply used a tape. I measured the highest, then made positive the underside matched earlier than driving in my screws to connect it.
Step 3: Attaching the Toe Kick Plate
Subsequent is to connect the toe kick, which ought to line up completely flush to each of the facet items and the entrance and the again. Identical with the again board that may make up the again of the platform as soon as this cupboard is stood up proper. Good, that’s the backside accomplished so now lets flip this round, however nonetheless depart it on it’s again, and begin engaged on the highest boards. This board right here will be part of the edges out on the again edge whereas additionally giving me a spot to screw it into the wall afterward when putting in it within the area.
When becoming a member of one thing flush like this, I like to maneuver my work piece to the sting of my workbench if doable. This manner my drill has room to go in straight as a substitute of at an angle the place I may blow out a screw.
Step 4: Attaching the Final Board
The final piece to connect here’s a related board because the final however this one joins the entrance fringe of the edges. Since I can’t use my workbench to relaxation it towards, what I love to do is use a clamp to behave as a 3rd hand. These squeeze clamps are nice to carry them within the common space whereas I get one facet at a time completely positioned and hooked up. This board will give me one thing to screw up right into a countertop later when it will get put in.
Step 5: Including the Again to the Laundry Drawer
Okay, with that hooked up, now let me spin this round, tilt it up, and similar to that we now have a cupboard. Oh, I forgot the again. Maintain on, that’s a fast add. Lets simply lay this factor again down, however this time laying it on it’s face. I made the again from 1/4” mdf because it doesn’t have to be tremendous thick. 1/4” materials will do a terrific job at holding it sq. and preserving it from racking.
You’ll see that my again is in two items. That’s as a result of I’m utilizing scraps and don’t care in regards to the again, which will probably be on the within and by no means seen, has a appear. If it does hassle you although, you possibly can all the time make it from one strong piece
Alrighty, and now that’s a accomplished physique. So for now, lets simply slide this on over to make room for me to herald the components to construct out the within drawer that may maintain the baskets.
Step 6: Securing the Match and Attaching the Sides
All of those components are additionally included on the plans and cutlist however I seize for what would be the backside first. I personally all the time like to ensure it matches inside the physique earlier than attaching issues simply because I’ve been recognized to seize the incorrect half earlier than however as soon as I made positive it match, I hooked up the 2 sides which appear to be wings. These have dados reduce into them for the underside to slide proper into.
This backside will probably be locked in as soon as the back and front are hooked up, however I went forward and threw in just a few screws. I went to the again and hooked up the specialty designed again. These slots and these predrilled via holes are wanted for the beneath mount drawer slides that I’ll be utilizing.
In case you use my precise dimensions then you cannot solely use the precise hampers that match on this laundry drawer but in addition the precise drawer slides. Nevertheless, know that if you wish to change dimensions then you definitely’ll most likely must get completely different drawer slides and alter the design of this again half. Another choice is to vary the scale to what you need, however then use facet mount drawer slides and never fear in regards to the beneath mount ones. Numerous choices.
Step 7: Finishing the Entrance Meeting
Going to the entrance of this meeting, I connect the massive entrance panel. This may appear massive and boring proper now however you’ll see why the size is required. For now, let me go forward and put it contained in the physique to ensure all of it seems to be good……annnnd it does. It’s so simple as that, now all the things right here on out are ending particulars.
Step 8: Making the Laundry Drawer Slide!
I may connect the beneath mount drawer slides to the underside facet of the cupboard. Appears like this right here. Then go to the within of the cupboard and connect the rails with screws. To attach the 2, I may carry the within portion over to the physique, set it on the rails, then push it in till the 2 elements clicked collectively. It’s so satisfying. Then since I’m making mine appear to be two doorways and a prime drawer, I crawled inside and hooked up these items to the surface by screwing them in on the within whereas Jacob held them to the correcting spacing.
Conclusion: The Completed Product
It’s kinda laborious to get a superb angle of this cupboard as a result of the area is de facto tight however with out the counter prime in place you possibly can see the way it works. Two hampers match completely on the drawer with the intention to pull it out and toss in your garments, then disguise them away once more by pushing it in. Comfortable closed in fact.
Even with the countertop on, I’ve loads of room to take the baskets out and in or just toss in garments then reshut it. I like the way it seems to be like three elements. The place because the unit on the left actually is a prime drawer and two doorways on the underside.
I’ve a 4 half sequence of movies the place I cowl how one can correctly paint MDF, how one can construct customized cupboards, how one can improve retailer purchased cupboards, and likewise how one can construct a countertop from scrap 2x4s! So mainly if you wish to see how I constructed out your complete room you’re taking a look at, then examine the hyperlinks within the description. In case you can think about it, you possibly can construct it and I hope I’m an inspiration or information that will help you get began. I’ll see you on my subsequent undertaking.
