For those who’re on the lookout for a spot to retailer your firewood that is also tremendous cool to have a look at, try this firewood holder DIY. Earlier than, I’d simply have my totally different sizes piled up in containers across the fireside, which was actually unattractive. So on a whim I threw these collectively. The three compartments permit me to separate small, from medium, to giant items of wooden. Seize a set of plans and let me present you the way I construct them.
Let’s Construct A Firewood Holder
DIY Firewood Holder Plans
$9.99
I’ve created a set of plans to make constructing this firewood holder fast and straightforward!
Supplies I Used on this Construct:
Step 1: Choosing Materials and Slicing to Measurement
I did design and construct these on a whim so when choosing materials, I simply regarded round my store to see what I had already that will match the sizes. I discovered this stack of three/4” reduce off from some cabinets I tore an element that I’ll make the physique from. Then for the again, I’ve some 1/2” plywood from who is aware of what.
I began off by ripping the sheets all the way down to width wanted. If you’d like actual dimensions, I’ve a set of plans obtainable over on my web site. I tilted the blade over to then reduce within the angles wanted to created the pointed miters. Since there are plenty of repeated components, I arrange a cease block in order that I may make all of them the identical. While you do that, you wish to be certain to set the cease block again far sufficient so the board received’t be touching it when it contacts the blade. As that is what may cause relax.
To save lots of from switching the blade backwards and forwards, after reducing one aspect with the wanted angle, I’d flip the board and reduce the opposite aspect because it nonetheless had a 90 on one finish. This can go away the remaining board with angles on each finish, that I can chop up for the mitered components. I personally prefer to at all times do a check first and a dry match to ensure issues are going to work as I’ve them deliberate. That appears good although.
Step 2: Banding the Edges of the Firewood Holder
Now I simply wanted 12 of them complete so I locked within the new distance for the fence for this half and chopped up the remaining bit into items.
This venture solely consist of 4 totally different components. What I’ll name the aspect, the tops that are barely longer than anything, the horizontal cabinets, then the mitered factors. Needless to say it will be easy so as to add extra to subtract the variety of cubbies, relying in your areas wants.
Alrighty, now I’ll edge band the perimeters that might be dealing with the entrance. Truly, on second thought, I like the concept of portray them as a substitute. Observe: that in case you edge band you’ll want to try this earlier than becoming a member of the components collectively, however if you wish to paint, then you possibly can go straight into assembling.
Step 3: Assembling the Firewood Holder Cubicles
For assembling, I began off on prime of my workbench and what I did is apply some wooden glue, I’m utilizing DAPs weldwood right here, to each joint, then pin nailed issues collectively utilizing my 23 gauge nailer. It is a fairly weak joint till the wooden glue has time to arrange, so I used to be being cautious as I used to be shifting it round to connect the subsequent leg. If I didn’t have a 23 gauge, I’d have used a 18 gauge as a substitute.
After getting a couple of hooked up, I believed it will make issues simpler to do it on the bottom so I may see all the pieces clearly as I used to be attaching legs. So I moved it all the way down to the ground and continued. I’d juke and jive to create the factors of the cubbies, then connect the horizontal that can create the separation between.
I paused once I obtained to the very prime as a result of the best way I’ve it designed, the highest edge will truly be seen. With that, I edge banded each of those components earlier than including them on. This is so simple as heating up an iron and warming up the glue on the again of the banding till it sticks to the plywood edge. This might be barely totally different than the ply, however it doesn’t hassle me.
Step 4: Portray the Firewood Holder Cubbies
I left that the place it sat to present that glue time to arrange and dry. Whereas it was, I grabbed items that can make up the again from my 1/2” plywood scraps. I additionally grabbed the items that can make up the edges. I need each of those to be painted the identical shade as my wall which suggests I want to present them a couple of coats earlier than attaching the cubbies.
Since I’ve the paint out, I additionally needed to color that entrance fringe of the cubbies. I first give them each an excellent sanding to get them clean. Now when working with plywood, there are usually voids on each single edge. As a way to get a clean wanting paint floor, I apply some wooden filler on a putty knife. I’m utilizing DAP Premium wooden filler. These items not solely dries quick however is straightforward to sand and is nice to paint match if you’re staining one thing.
After letting it dry for about 30 minutes, I got here again with a sanding sponge to knock it down flat in order that I may roll on the paint onto the items of the firewood holder.
With ending out of the best way, let me simply push this button right here to lift my ending shelf up and find the {hardware} I’ll want to connect the cubbies to the again.
Step 5: Shaping the Again to Match the Firewood Holder Cubbies
I began with a again barely bigger than what I wanted, then plopped the cubbies down onto it and lined it up in order that the underside cubby was flush to the top of the plywood. I used my pin nailer to only tack issues in place to start out. The top is straightforward accurately flush, however to ensure the remainder weren’t crocked, I pulled a tape to get the spacing excellent earlier than tacking the remainder. With it not capable of fall off now, I tilted the complete unit on it’s face in order that I’d have entry to the underside to throw in screws. Right here, I made certain to pre drill to stop splitting.
Step 6: Securing the Firewood Holder Cubbies to the Again
The highest location is straightforward to find as a result of you may have a visible on the place the shelf is positioned. Nonetheless, the second is hard as a result of it’s in the course of nowhere. What I do is seize a pace sq., this Crescent one has an extra 6” flip out rule in order that I can place it within the heart of the shelf, go all the way down to the dimension wanted, and pre drill. For those who don’t have this pace sq. or one other lengthy one, then a stage would additionally do the trick.
For the angled portion of the cabinets, the pace sq. wouldn’t work, so I grabbed a scrap and reduce in an angle on the tip. This manner I may relaxation it on the shelf and permit me to mark the peak. Ensuring to maintain it in the identical location, I moved the scrap to the face closest to me to now drop it down again to the road I made which supplies me the situation of the angled shelf to pre drill and fasten a screw.
With the again on, this factor now feels actually safe and powerful. I flipped it up to have a look. I truly suppose it appears fairly good with a sq. again on it and was contemplating leaving it as is however then I made a decision to stay to my authentic plan and make the again flush to the geometric form. I wasn’t capable of find my palm router, which is definitely the best software to trim the again off, so as a substitute I put a flush trim bit in my router desk and trim it off that approach. The important thing right here is to maintain the unit good and flush on the desk as you progress it alongside.
I laid the unit over and hooked up the aspect. This can assist help the horizontal cabinets that can truly be supporting the load of the firewood.
Step 7 : Putting in the Firewood Holder and Slicing Firewood
Final thing to do was set up them. Now I personally needed mine up off the bottom so I wouldn’t block an outlet I’ve over on the best hand aspect. Then I additionally like to make use of this space for storing my video games and puzzles. With that, I propped the models up, discovered the studs, then drove a couple of screws into the again of the unit to connect them.
Okay lets load it down and see how a lot it might maintain. Now that, is significantly better than earlier than. As a substitute of ugly containers and totes, I now have a pleasant firewood holder with devoted house for the wooden. This can permit me room to retailer and separate all totally different sizes of firewood throughout winter. Then I personally just like the look of wooden sufficient to maintain it full yr spherical, however I may additionally retailer different kinds of nicknacks throughout spring and summer time ought to I wish to.
What do y’all take into consideration them? Keep in mind how straightforward it’s to make bigger or smaller. I even suppose they’d look good horizontal, relying in your house. I’ve a set of plans for this venture in addition to many different over on my web site. Actually, if you need firewood storage concepts, I’ve a couple of of them.
I’ll see you subsequent time.